This over/under voltage cut-out will save your costly electrical and electronic appliances from the adverse effects of very high and very low mains voltages. The circuit features auto reset and utilises easily available components. It makes use of the comparators available inside 555 timer ICs. Supply is tapped from different points of the power supply circuit for relay and control circuit operation to achieve reliability. The circuit utilises comparator 2 for control while comparator 1 output (connected to reset pin R) is kept low by shorting pins 5 and 6 of 555 IC. The positive input pin of comparator 2 is at 1/3rd of Vcc voltage . Thus as long as negative input pin 2 is less positive than 1/3 Vcc, comparator 2 output is high and the internal flip-flop is set, i.e. its Q output (pin 3) is high. At the same time pin 7 is in high impedance state and LED connected to pin 7 is therefore off. The output (at pin 3) reverses (goes low) when pin 2 is taken more positive than 1/3 Vcc. At the same time pin 7 goes low (as Q ouptput* of internal flip- flop is high) and the LED connected to pin 7 is lit. Both timers (IC1 and IC2) are configured to function in the same fashion. Preset VR1 is adjusted for under voltage (say 160 volts) cut-out by observing that LED1 just lights up when mains voltage is slightly greater than 160V AC. At this setting the output at pin 3 of IC1 is low and transistor T1 is in cut-off state. As a result RESET* pin 4 of IC2 is held high since it is connected to Vcc via 100 kilo-ohm resistor R4. Preset VR2 is adjusted for over voltage (say 270V AC) cut-out by observing that LED2 just extinguishes when the mains voltage is slightly less than 270V AC. With RESET* pin 4 of IC2 high, the output pin 3 is also high. As a result transistor T2 conducts and energises relay RL1, connecting load to power supply via its N/O contacts. This is the situation as long as mains voltage is greater than 160V AC but less than 270V AC. When mains voltage goes beyond 270V AC, it causes output pin 3 of IC2 to go low and cut-off transistor T2 and de-energise relay RL1, in spite of RESET* pin 4 still being high. When mains voltage goes below 160V AC, IC1’s pin 3 goes high and LED1 is extinguished. The high output at pin 3 results in conduction of transistor T1. As a result collector of transistor T1 as also RESET* pin 4 of IC2 are pulled low. Thus output of IC2 goes low and transistor T2 does not conduct. As a result relay RL1 is de-energised, which causes load to be disconnected from the supply. When mains voltage again goes beyond 160V AC (but less than 270V AC) the relay again energises to connect the load to power supply
Thông báo
Collapse
No announcement yet.
Cắt mạch khi quá áp hoặc dưới áp
Collapse
X
-
Cắt mạch khi quá áp hoặc dưới áp
This over/under voltage cut-out will save your costly electrical and electronic appliances from the adverse effects of very high and very low mains voltages. The circuit features auto reset and utilises easily available components. It makes use of the comparators available inside 555 timer ICs. Supply is tapped from different points of the power supply circuit for relay and control circuit operation to achieve reliability. The circuit utilises comparator 2 for control while comparator 1 output (connected to reset pin R) is kept low by shorting pins 5 and 6 of 555 IC. The positive input pin of comparator 2 is at 1/3rd of Vcc voltage . Thus as long as negative input pin 2 is less positive than 1/3 Vcc, comparator 2 output is high and the internal flip-flop is set, i.e. its Q output (pin 3) is high. At the same time pin 7 is in high impedance state and LED connected to pin 7 is therefore off. The output (at pin 3) reverses (goes low) when pin 2 is taken more positive than 1/3 Vcc. At the same time pin 7 goes low (as Q ouptput* of internal flip- flop is high) and the LED connected to pin 7 is lit. Both timers (IC1 and IC2) are configured to function in the same fashion. Preset VR1 is adjusted for under voltage (say 160 volts) cut-out by observing that LED1 just lights up when mains voltage is slightly greater than 160V AC. At this setting the output at pin 3 of IC1 is low and transistor T1 is in cut-off state. As a result RESET* pin 4 of IC2 is held high since it is connected to Vcc via 100 kilo-ohm resistor R4. Preset VR2 is adjusted for over voltage (say 270V AC) cut-out by observing that LED2 just extinguishes when the mains voltage is slightly less than 270V AC. With RESET* pin 4 of IC2 high, the output pin 3 is also high. As a result transistor T2 conducts and energises relay RL1, connecting load to power supply via its N/O contacts. This is the situation as long as mains voltage is greater than 160V AC but less than 270V AC. When mains voltage goes beyond 270V AC, it causes output pin 3 of IC2 to go low and cut-off transistor T2 and de-energise relay RL1, in spite of RESET* pin 4 still being high. When mains voltage goes below 160V AC, IC1’s pin 3 goes high and LED1 is extinguished. The high output at pin 3 results in conduction of transistor T1. As a result collector of transistor T1 as also RESET* pin 4 of IC2 are pulled low. Thus output of IC2 goes low and transistor T2 does not conduct. As a result relay RL1 is de-energised, which causes load to be disconnected from the supply. When mains voltage again goes beyond 160V AC (but less than 270V AC) the relay again energises to connect the load to power supplyTags: None
-
Theo bài trên thì mạch sẽ cắt khi điện áp dưới 160 hay trên 270V.
Cho tôi hỏi:
Dòng đem so sánh ta đã ổn định mức 9V rồi thì
- Con 555 sẽ so áp như thế nào? Theo mạch trên thì khi ta cho điện áp ngõ vào 160V (low) chiết áp VR1 ta sẽ chỉnh cho chân số 2 xuống thấp hơn mức 3V (1/3 của 9V) thì dòng ở pin 2 sẽ là ứng với mức khi dòng ngoài 160V.
Comment
-
mach bao ve phu tai
Đây là một mạch em sưu tầm được các bác xem thữ và thấy khả quan thì cho ý kiến để em ráp nhé.cảm ơn các bác nhiều!Attached Files
Comment
Bài viết mới nhất
Collapse
-
Trả lời cho Khác nhau giữa mạch cân bằng chủ động toàn dãy và mạch cân bằng chủ động kiểu so áp 2 string liền kề.bởi louisnkCụ đã lên design chi tiết cho mạch để test chưa?
-
Channel: Điện tử dành cho người mới bắt đầu
19-09-2024, 08:12 -
-
bởi Manh.n.trMọi người cho em hỏi có bác nào làm project mạch đo độ mặn chưa ạ. Cho em hỏi có bác nào mô phỏng được trên Proteus không ạ? Em sinh viên đầu năm 3 tay mơ chưa biết nhiều mong mọi người giúp đỡ ạ
-
Channel: Các mạch điện ứng dụng
17-09-2024, 13:54 -
-
Trả lời cho Xin hỏi về mạch khuếch đạibởi yname11Ko đc bác ạ, mạch nó tự ngắt. Thôi đành dùng 1 kênh vậy, thanks bác nhé....
-
Channel: Điện thanh
15-09-2024, 10:44 -
-
bởi nguyendinhvanTôi thì không học về MCU, không giỏi về VXL , cũng mờ tịt về công nghiệp thực phẩm, nhưng cũng cố gắng tự làm được cái này.
Đồ ở chợ mua về cứ đặt ở sân, rồi xếp cái máy này lên trên, rồi đi chơi.
Một lúc sau quay...-
Channel: Tâm tình dân kỹ thuật
15-09-2024, 02:36 -
-
Trả lời cho Thép hàn cube led ???bởi nguyendinhvanRa chợ kim khí mua, có nhiều loại to nhỏ. Họ bán cho thợ xây dựng buộc khung đúc bê tông.
Về cắt thành đoạn.
Nhưng làm cho các đoạn dây thép đó thẳng tưng như cái gói mì Ý, thì cũng đòi hỏi công nghệ khéo tay.-
Channel: Điện tử dành cho người mới bắt đầu
15-09-2024, 02:03 -
-
Trả lời cho Thép hàn cube led ???bởi bqvietThép nào cũng hàn thiếc được : thép các-bon, thép không gỉ ... miễn là có chất trợ dung phù hợp. Dùng nhựa thông bình thường thì khó hàn, nhưng trên thị trường bán nhiều loại chất trợ dung đủ kiểu. Đơn giản nhất là dung dịch kẽm clorua ZnCl2.
-
Channel: Điện tử dành cho người mới bắt đầu
15-09-2024, 00:34 -
-
bởi tuyenda1985Các bác cho em hỏi.
Định làm cube led chơi chơi, nhưng vụ que thép để cho nó cứng
Mà chưa biết mua ntn, vì đang alwn tăn, loại này là loại nào (như hình em úp) mà có thể dùng thiếc hàn ??
Cảm ơn...-
Channel: Điện tử dành cho người mới bắt đầu
14-09-2024, 22:05 -
-
Trả lời cho Xin hỏi về mạch khuếch đạibởi thetungPhương án của bạn có thể được ,nhưng có thể rủi ro . Mặt khác bạn muốn tăng công suất thì phải giảm trở kháng của loa ( thí dụ dùng loa 2 ohm )...
-
Channel: Điện thanh
14-09-2024, 11:46 -
-
Trả lời cho Xin hỏi về mạch khuếch đạibởi yname11chập 2 đầu r+, l+ vào làm 1, 2 đầu r-, l- vào làm 1 . rồi đấu vào loa...
-
Channel: Điện thanh
14-09-2024, 07:40 -
-
Trả lời cho Em là người mới . Xin các bác chỉ giáo cách mod điều chỉnh điện áp trên nguồn DELTA esr 48/56abởi nguyendinhvanTheo tôi ấy, mấy cái hệ delta powerone ấy. Cứ để in như thế bán lấy tiền ăn phở.
Có chất bổ vào người, đầu sẽ thông minh ra, sau đó tự nghiên cứu chế tạo một cái nguồn theo ý mình.
Thế là vừa được thông minh, vừa được...-
Channel: Điện tử dành cho người mới bắt đầu
14-09-2024, 01:33 -
Comment